See our newest Products.

New Cable Workshop Surge Generator

Adret SG80034 - Surge Generator
Morné Steffens Senior Production Manager at Adret, South Africa talks though the features and functions of the Adret SG80034 - Surge Generator

Updated Cable Identifier

Adret Ci75 Cable Identifier
Morné Steffens Senior Production Manager at Adret, South Africa talks though the features and functions of the Adret Ci75 Cable Identifier.

Surge Generator - Adret SG80034

  • Surge Generator

    • Output Voltage: 7.5, 17, 34kV 1450 Joule (Ws)

    • Pulse Rate: Every 4 Seconds (15PPM)

    • Mains Condition Lockout System

    • Checks Mains input High

    • Checks Mains Input Low

    • Checks Mains Polarity Correct

    • Checks Earthing Integrity

  • 34KV 1450 Joule Mining Cable Shop Surge Generator

    • New stainless steel enclosure

    • 10 earth leads

    • Additional milliamp reading

    • Cabinet has wheels for easy transport

    • Perspex cover lid for protection

  • https://www.youtube.com/watch?v=1tnXTCC2AK8

  • Designed for Australian conditions

    • Delivery time 4-6 weeks

Cable Repair Tapes

  • PCP 0.64mm x 25mm x 0.5kg
    PCP 0.64mm x 50mm x 1.0kg
    CSP - Yellow - 0.64mm x 50mm x 1.0kg
    CSP - Red - 0.64mm x 50mm x 1.0kg
    CSP - Green - 0.64mm x 50mm x 1.0kg
    EPR - Flame resistant EPR
    PCP semi con (25mm)
    PCP semi con (50mm)

  • Designed for Australian conditions.

    • Stock on hand

    • Special order delivery time 4-6 weeks

Cable Vulcanizer

  • Cable Vulcanizers are used to bake the rubber in and around the cable. Essential for all repairs and cable joints/splices.

  • Suitable for cable sizes from:

    10mm-80mm diameter cable

  • Designed and built in Australia.

    • Made to order

    • Delivery time 4-6 weeks

Symmetrical Load Tester

  • A Symmetrical Load Tester is an important device used to test that repaired 3 phase trailing cables are operating electrically symmetrical. Australian Standards require all mining cables pass this test before returning to service.

  • 15 or 20 KVA - 3 Phase transformer 

    415 Volt Primary to 31 Volt Secondary @ a maximum load of 385 Amps output

    • Variac 3 Phase - Maximum load 28Amps

    • Diris A-30 Power Meter - Which reads the three individual phase currents.

    • 3 x Current Transformers (ratio 500/5)

    • 1 x Milliamp Meter - Which reads the milliamp leakage injected into the earth conductors.

    • Timers designed for 30 seconds (30 sec on) operation time and 2 minutes cool down time (2min off). 

    • Emergency Stop Button


    • Run Button


    • Power on keyed Button


    • 3 x 5 metres of test leads 

    • 120mm² single core cable

    • 10 metres of main lead - 20Amp 4 pin plug

    • Unit comes in a powder coated 1.5mm Galvabond (IP21) steel enclosure

    • Wheels: fixed and swivel (with break) wheels

    • Custom connecting pins to suit cables under test (to be advised by customer)

    • Total size: 1600mm x 600mm x 850mm

    • Total weight: 320kg

  • Designed and built in Australia.

  • Download the PDF manual

  • Made to order
    8-10 weeks

Partial Break Hammer

  • The Partial Break Hammer physically manipulates the cable while tests are conducted with the Partial Break Testing unit. The cable is drawn through the unit (in the same way as it is with the cable handler) with an additional mechanical agitation. This allows the test to detect faults that would otherwise be undetected when the cable is laid flat.

    • 1.5KW 415V Motor coupled to a flange mounted gearbox with a 10:1 reduction

    • Rotating hammer is driven by 0.75kW 415V motor and Vee belt drive

    • Adjustable pressure rollers

    • Foward/Reverse/stop control

    • 10m flexible rubber power lead with 20Amp four pin plug

    • Tool shelf

    • Emergency Stop

  • 18mm-85mm cable diameter

  • To be advised by client

  • Designed and built in Australia.

  • made to order
    4-6 week

Cable Drum Roller - Large

  • Used to wind cables back on and off cable drums

  • GANDA Drum Roller (Large)

    • Take drums up to 2400mm wide

    • Fabricated frame with fork pockets

    • Plain steel rollers and bearings

    • 10m of hoses and quick connect couplings and fittings

    • Remote control & transmitter with proportional button and Estop

    • 2 x 400cc hydraulic motors

    • 60l of hydraulic oil (supplied)

    • 15m of electrical cable and 20 Amp plug.

    • Hydraulic system:
      Power unit 75 ltr tank 7.5 kw with proportional flow.

    • Powerpack has inside fabricated frame with forklift pockets and lifting points and quick release holes.

  • Colour to be advised by client

  • Designed and built in Australia.

  • Download PDF manual

  • Made to order
    8-10 weeks

Test Pins

  • Case Hardened Steel Test Pins.

    • Each pin is calibrated with sticker.

    • Precision made and calibrated

    • Pins come with foam protected Pelican Case.

  • Seven (7) pins sizes:

    • 6.32 dia pin

    • 7.90 dia pin

    • 9.50 dia pin

    • 11.07 dia pin

    • 12.67 dia pin

    • 15.85 dia pin

    • 19.02 dia pin

  • Designed and built in Australia.

    • Made to order

    • Delivery time 4-6 weeks

Cable Vulcanizer - Large (Prototype)

  • Cable Vulcanizers are used to bake the rubber in and around the cable. Essential for all repairs and cable joints/splices.

  • Cable Sizes

    Suitable for cable sizes from:

    80-130mm diameter cable

  • Designed and built in Australia.

    • Made to order

    • Delivery time 8-12 weeks

Go/No-Go Test Rings

  • Go/No-Go Rings are used to check that Restrained Electrical Plugs (Mining plugs) meet Australian Standards for flame proof safety.

  • Set of three (3) test gauge rings in hollow bar medium strength high tensile (similar to 1045) in 3 different sizes.

    • 60amp earth sleeve

    • 125/150 earth sleeve

    • 300/425 earth sleeve

  • Designed and built in Australia.

    • Made to order

    • Delivery time 4-6 weeks

Cable Handler

  • Cable Handlers are used to mechanically move cables around the workshop, off trucks, onto palettes, over to repair workbench etc.

    • 4 kW / 415V motor 1:15 reduction with a 35mm output shaft

    • Lenze Protec Inverter for speed control

    • Variable Speed controller

    • Emergency Stop

    • 10m flexible rubber power lead with 20Amp round pin plug

    • Heavy duty 150mm casters with brakes

  • Suitable for cable sizes from:

    10mm-120mm diameter cable

  • Paint colours to be advised

  • Designed and built in Australia.

  • Download the PDF manual

  • Made to order
    4-6 weeks

Cable Sheath Tester

  • A Sheath Tester detects pin holes and other damage to the outer sheath of tailing cables.

    Unit operates from 0kV to 15kV. Buzzer and light when fault is detected.

  • 10mm-120mm cable diameter

  • To be advised by client

  • Designed and built in Australia.

  • made to order
    8-10 weeks

Cable Drum Reeler - Small

  • Specs

    • Take drums up to 1300mm wide

    • Capacity 2.5 Tonne

    • Fork pockets for easy transport

    • Plain steel rollers and bearings

    • Polyethylene coated drive roller

    • Adjustable idle position

    for various drum sizes

    • Foot switch

    • 10m of electrical cable

    and 20 Amp plug

    • Duplex chain drive

    • 1.5 kW motor with reduction gearbox and soft start.

  • Designed and built in Australia.

    • made to order

    • 4-6 weeks

  • Download the brochure